We use many different types of communication in control applications to control home appliances, industrial appliances, and other type of automation. There are two types of communication that is we generally use - one is wired and other one is wireless. In wireless communication we transmits signal wirelessly, like using radio frequency (RF) and in wired communication in which we uses wires like copper wire. In this project “DTMF Based Home Automation System” we are going to control our home appliances wirelessly. Other important feature of this project is, that we are not going to use any microcontroller in it.
Required Components
- MT8870 DTMF Decoder -1
- ULN2003 -1
- Relay 5 volt -3
- Bulb with holder or LED -3
- Connecting wires
- Bread board -2
- Aux Wire -1
- 9 volt battery -2
- PVT or Terminal Block -4
- 100K Resistor -2
- 330K resistor -1
- 0.1 uf Cap -2
- 22 pF cap -2
- 3.57 Mhz Crystal -1
- Mobile phone
- LEDs -3
- 1K resistor -6
- 7805 -1
Circuit Concept and Working
DTMF controlled home appliances project works over mobile DTMF technology that exists in Dial tone. DTMF stands for Dual Tone Multiple Frequency. There are some frequencies that we used to create DTMF tone. In simple words by adding or mixing two or more frequencies generates DTMF tone (Also check: DTMF Based Robot using Arduino). These frequencies are given below:
In Given figure we can see two groups of different frequencies. When one upper and one lower frequencies mixed then a tone is created that tone we calls Dual Tone Multiple Frequency. In this project we control ac appliances by pressing dial pad keys like 1, 2, 3, 4, 5 and more.
Here we have connected a cell phone using aux wire to the DTMF decoder circuit. Before explaining the further working of project we need to know about the output of DTMF decoder for every key pressed.
Now understand working according to given table.
In circuit diagram at Q1 LIGHT is connected, at Q2 FAN is connected and at Q3 TV is connected through relay driver IC. We have left Q4. Now when we press key 1 at the dial pad of mobile phone DTMF decodes this tone and generates a digital output given in table. Now According to given output in table Q1 is HIGH and Q1 is connected with light so LIGHT turned ON. If we want turned OFF the LIGHT, we need to press key number 8. Because in the output of key8, Q1, Q2 and Q3 LOW and Q4 are HIGH and we have not used Q4. So it doesn’t matter that Q4 is HIGH or LOW. But our operation has been performed because Q1 is LOW in key 8’s output and rest of appliances not affected. Now is we want to turned on FAN so we need to press key2 because by pressing key2 only Q2 is activated and rest of output are remain same. Now if we to OFF the FAN then we need to press key8 again like before for as LIGHT. Now if we want to TV so we need to press key4 and for tuning it OFF we need to press 8 like before. Now suppose we want to turned ON all of the appliances so we need to press key7 (see table) and for turning OFF all key8 (see table).
Now if we need to ON LIGHT and FAN so we need to press key3 (see table). And now we want to ON TV so we need to press key 7 not key4. Because we should keep remain turn ON previous appliances. Now if we want to turn OFF only LIGHT so we need to press key6. Because we should again to keep remain turn ON the previous appliances except LIGHT.
So we can control each of the appliances according to table output.
Circuit Diagram and Explanation
Circuit diagram for DTMF controlled home automation project is shown above. In this circuit we have used a DTMF decoder namely MT8890 IC which converts dial pad tone into the four bit digital output. LIGHT, FAN and TV are connected to Q1,Q2 and Q3 of DTMF decoder IC through a relay driver namely ULN2003. 5 volt SPDT 3 relays are used for controlling LIGHT, FAN and TV.
For demonstration of this project we have connected three LEDs at relay instead AC appliances. And we have also used 9 volt dc battery instead 220VAC for driving LEDs.
Comments
i wanna do a project concerning about DTMF
very nice project .it helps me a lot
how can i know the aux cable
how can i know the aux cable is worked or not, i juz cut my earphone to test it but it didn't work
plz suggest me
@Lyan Leon Please check this
@Lyan Leon Please check this article for AUX cable connections and description: Small Loudspeaker
Is your project working? If
Is your project working? If yes, then would you mind contacting us. we really need your help. Contact us on [email protected]
How have you connected the
How have you connected the aux cable to the dtmf decoder chip? please help me.
You need to cut the one end
You need to cut the one end of AUX cable and take out its wires, and connect them to breadboard. Check this Article for Aux cable connections: Small Loudspeaker
Simulation
For simulation of this circuit which software is more efficient?
by using four 4 or 5 push
by using four 4 or 5 push buttons you can simulate it at proteus.
can we drive a electric fan
can we drive a electric fan working on ac power supply at home using this circuit?how can we do this?please help us.
yes, you can drive any AC
yes, you can drive any AC home appliances.
can we use ht9170 decoder
can we use ht9170 decoder instead of mt8870?
why uln2003 used
hey saddam here u use uln2003 but why u use that if u connect that directly than also it work
and i want that from pressing 1 like tv on again pressing 1 it off the tv how will i do this
Sir, what is the use of the
Sir, what is the use of the other 4 led(3 red and 1 yellow), would u plz explain?
These are indication LEDs,
These are indication LEDs, when we connect the actual AC appliances in places of 3 LEDs at the Right side, then these LEDs work as indicators.
All the led's are not going
All the led's are not going off after pressing 8,( my circuit is correct)??
Engineering
Can we control home appliances using dtmf tone, through wifi lan connection...if yes then please send me a solution, that how it will work..
please let me know the use of
please let me know the use of ULN2003 driver in this project?
Can you please help me
Can you please help me understand how this is a wireless solution?? The mobile is connected to the circuit through the AUX cable as I see it. I would really like a wireless version of this. Thank You
Can u plz tel me how to
Can u plz tel me how to connect this on pcb
Can v operate this from any
Can v operate this from any place???
DTMF based home automation
Just interested in this project and wanna know like how much does it cost, like the entire project
PVT is Terminal Block, Green
PVT is Terminal Block, Green color block adjacent to each Relay (see picture), to secure wires with screws.
Can we make circuit in pcb
Can we make circuit in pcb board? And can we use tv on output side instead of led
There are so many softwares
There are so many softwares are available for Schematic to PCB layout conversion like Easy EDA, Fritzing etc, check this: Design Your Circuits Online for Free with EasyEDA and Yes you can use any electronic AC appliances to be controlled.
You can use the same circuit
You can use the same circuit but you have to replace the Relay for handling 440 v, the relay used in this circuit can handle upto 250v.
sir........
sir........
what are the function of pin number 5&6 of IC MT8870?
sir; wat happen
sir; wat happen
to the cct wen i dropped d cal.. will the cct stil b active
Yes, It will remain in the
Yes, It will remain in the same state.
what is pvt in the component list
Many people keep asking whats pvt .no one answered that. Someone please tell what does pvt stand for atleast??!
PVT is Terminal Block, Green
PVT is Terminal Block, Green color block adjacent to each Relay (see picture), to secure wires with screws.
I know its a lot to ask but
I know its a lot to ask but Can you send me the final project Report of this it'll be really helpful and Thank you very much the project is really Great and its working Perfectly.
I want to control the
I want to control the appliances wirelessly (using another phone to control the whole circuit). can any one help me out with the necessary things to add?
You can control it via other
You can control it via other phone, just call on the mobile phone near the circuit and dial the no from the other phone, check this circuit video for more detail.
Can I use 3.579mhz Crystal
Can I use 3.579mhz Crystal .plz help me immediately
circuit doesnot working
I made this circuit on pcb as per diagram but it's not working.
led 1,2,3 is continuously on and IC MT8870 is heating more.
please let me know what should I do?
I am waiting your response.
can I connect DTMF IC
can I connect DTMF IC directly to relay?
what is a roll of driver ic?
Relay should be used with a
Relay should be used with a driver circuit of Transistor and diode to make it work properly, check here for more detail. And ULN2003 IC has inbuilt darlington transistor pairs and other circuitry to drive relay.
You can use only one battery
You can use only one battery as per circuit diagram.
circuit is working but when I
circuit is working but when I press 2 or 3 it will turn on one relay ,then if I press 4 or 5 button it will on 2nd relay, at a time all 3 relay r not conducting plz help me fast
plz reply......
DTMF controlled home automation
How to prevent calls from other mobile and mall functioning of DTMF decoder as any one can dial mobile connected to circuit. I want exclusive control with only specific mobile.
Thanks
Easiest way is to use
Easiest way is to use exclusive sim card for that mobile, otherwise you need use some microcontroller and GSM module to filter the incoming mobile number.
I can control it from
I can control it from anywhere. Another mobile calls.?
switch off the load by mobile ,if already on from starting.
Sir,it says,that whenever we forget to switch off the appliances,that time this circuit is used.But sir,in video,we have to keep on our appliances and off,when phone call is dialled.but when switch is already on,and if we want to switch off the appliance,then how we do that?.because,if we off the switch during phone call,after phone call ends,the appliances will remain on.so,the purpose is not achieved.please please tell me.
If you switch off the
If you switch off the appliance from the mobile then it will remain off, whether the main switch is on
It's Not Working
Hey,
I made this circuit on PCB it can not working. At the time of starting when i connect the supply directly 12 and 13 pin LED is start to glow without any given input. please help sir.
we can get out put with out relays
We can get out put with out relays
how to implement this project
how to implement this project on software, please help me
Simulation program
What is the name of the simulation program please ?
Please read the above
Please read the above comments before posting, your question might have already answered.
What if I use headphone jack
What if I use headphone jack instead of aux cable?
can i use any smartphone or
can i use any smartphone or is it necessary to use any specific phone to interface?
No, you can use Transistors
No, you can use Transistors to trigger LEDs. Relays are for the purpose of switching AC appliances.
We've been trying really hard
We've been trying really hard to run this project. Can anyone please help me out in any which way? If yes, then kindly contact us on [email protected]
DTMF home appliances
What is the use of crysal oscillator. In the circuit ??
Sir,i want to control the
Sir,i want to control the tubelight & fan which is operates on 230v-50hz power supply.can i use this ckt fr this .if yes ,what modefication is needed to do in ckt .plz reply
We implemented the circuit
We implemented the circuit but the leds remain on once we connect the battery..plzz help
Request For Help
Hello Sir.
I want to implement this project by using At328 microcontroller, can you help me how the circuit diagram will look like?,
Please,help me.
System Engineer
hello,
1. Is this all the circuit you got ??
2. Does it has any coding or not?
3. Did anyone has tried that?
There is no coding required,
There is no coding required, it should work as demonstarted
DTMF based home automation
What is the cost of the project....???
How much will be the cost for
How much will be the cost for the project
Will this project work if I will make a call at the receiver and then during call,press the buttons from the transmitter side. Please help me by explaining the working of each and every component. I beg u plz help me